Niski utovarivač

Fliegl ZTS 200 P

Additional Information
Chassis, Low-Bed Trailer
Steel welded construction
Turntable with robust ball bearing, storage box integrated into the turntable extension
Foldable rear support
Chocks with holder
Aluminum side impact protection
Half-shell fenders on the 1st axle, quarter-shell fenders in front of and behind the 2nd axle
with anti-splash flaps behind each axle
1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with padlock. (Lock not included)
Extensions extendable to 3,000 mm (not in rear slope)
(The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the center of the loading area, wooden planks 70 mm for extension to 3000 mm
Tie-down points, low-bed trailer
3 pairs of tie-down points, each 10 tons, integrated into the front of the floor
6 pairs of tie-down eyes, each 10 tons, embedded in the top and side of the outer frame
1 x in the neck area, the rest distributed in between, with a distance of no more than 1200 mm
1 x rear slope
5 pairs of ring tie-down points embedded in the outer frame, each 5 tons (instead of stringer pockets)
Coupling device, trailer turntable
Drawbar with tested 40 mm towing eye
Axles + Suspension
SAF drum brake axles
Axle/chassis laser-aligned to reduce tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing
Wheels and Tires
235/75R17.5
as chosen by the manufacturer
Steel rims in twin arrangement, factory silver
Braking System
2-line pneumatic brake system
Spring-loaded parking brake
2 non-interchangeable coupling heads at the front, with connecting lines to the tractor,
ABS and ALB, with ABS plug at the front, with connection cable
Note: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS!
Electrical System
24 Volt, multi-chamber lights, yellow LED lighting on the sides
2 white/red position lights at the rear
2 white position lights at the front
1 rotating beacon with holder, switched on via parking lights (beacon can be removed)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
2 x 7-pin non-interchangeable plugs at the front, with connection cable
Floor
Front area steel floor
then with 70 mm softwood floor, in the wheel arch area steel/diamond plate
Rear slope with 70 mm softwood floor
Low-bed area including rear slope 8,200 mm
Ramps
Steel ramps 2800 mm long, 750 mm wide, laterally adjustable
additional ramp securing device foldable at the bottom (to prevent the ramps from sliding sideways, not in conjunction with hydraulically adjustable ramps)
covered with wood
with spring-loaded support
Operating instructions
For a 10,000 kg axle load, a special permit is required. The permit must be applied for separately in each federal state; the legislator does not have to guarantee approval for 20 tons GVM. Customer risk.
The specified total weight is technically possible, depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads.
Approval / Signage
Psdpfx Aoi Ri N Hjfgepu
Country of approval: Germany
Type approval according to EC 2007/46
24/7 service hotline
prepared for license plate holder, two lines
Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear
Warning sign according to ECE - 70
Paint
Frame, DB Novagrau (DB Novagrau is a color)
Ramps, hot-dip galvanized

Note: Archive images!

Oglas je automatski preveden. Moguće su pogreške u prijevodu.