Niskopodni poluprikolicom

FAYMONVILLE Multimax Plus Satteltieflader Hebebett

Extract of Equipment SCHWANENHALS Gooseneck in SNT design to optimize the loading area length, approx. 3,700 mm long, rear with chamfer approx. 1,000 mm x 6°. For tractor units: 4 x 2 and 6 x 2. - ASPÖCK-UNIBOX - 3 kW electro-hydraulic power unit for control of hydraulic operations except for hydraulic cable winches. - Grating flooring with 5 mm steel plate reinforcement on the gooseneck and rear chamfer. - 2-inch king pin - Guide plate on the gooseneck for the fifth wheel plate, approx. 500 mm wide. - Round NATO socket at the front connector panel (Maeler & Kaege VG 96 917) - On the gooseneck, 1 pair of removable anodized ALU side panels, approx. 400 mm high. - 1 LED work light mounted left and right at the top front wall, wired to the connector panel for the tractor unit. LOADING AREA Loading area approx. 9,600 mm long, with rear chamfer approx. 900 mm x 6°. Loading area after the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg. - TPMS tire pressure monitoring system according to ECE R 141. - BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered trailing axle. 3rd axle with electro-magnetic reverse lock, activated by reverse gear or manually. Technical axle load: 12,000 kg each. Air suspension with raise/lower valve. - 235/75 R 17.5 3PMSF twin tires. Make at our discretion. - Mechanical landing legs with 2-speed gearbox and crank. JOST Modul B - static test load = approx. 50,000 kg - Continuous grating flooring with approx. 5 mm steel plate reinforcement for point loads, designed for: - on the lift bed - on the loading area - Painted-on sand coating on the gooseneck cover plates and transition areas: between neck and lift bed, lift bed and loading area, and loading area and ramps. - 1 spare wheel mounting bracket under the loading area right in front of the axles. - Cut-outs in the outer frame of the loading area and lift bed for attaching lashing straps (LC 2,000 daN). - 11 pairs of sunken lashing rings installed horizontally in the outer frame of the loading area, foldable outwards (LC 10,000 daN): - 3 pairs in the outer frame of the lift bed - 8 pairs in the outer frame of the loading area - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): - 3 pairs in the lift bed - 8 pairs in the rear section of the loading area - Control valves for the hydraulic ramps on the right side of the vehicle. - 1 pair of foldable mechanical rear supports with one-hand operation. - Operation of all work lights in the loading area via switches on the loading area itself (operation from tractor unit not possible in this case). - Audible reverse warning signal. HYDRAULIC LOADING RAMPS (DR-10-900-4920-GR-HV-AXS) 1 pair of two-piece AXS steel ramps approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically foldable ramp tips. Ramps individually hydraulically extendable approx. 235 mm outward and approx. 365 mm inward. - Grating surface and steel floor approx. 5 mm as additional reinforcement on rear chamfer of loading area - Flashing lights on the outer sides of the ramp tips, with switch next to ramp operation. - Ramp securing in travel position with quick-release lock. - Painted-on sand coating on the ramp outer frame.
Giodpfx Ajy Auhhoahor

Oglas je automatski preveden. Moguće su pogreške u prijevodu.